Author Topic: CG2 LED Traces ?  (Read 7080 times)

Offline Porkyfied

  • Guppy
  • *
  • Posts: 6
  • Post quality +0/-0
CG2 LED Traces ?
« on: April 29, 2012, 07:31:22 AM »
Hi i was wondering if anyone has a picture showing the led traces for a CG2 controller?

Offline Rodent

  • XBOX,XBOX360,PS3,WII
  • Moderator
  • Around the block
  • *
  • Posts: 2983
  • Post quality +75/-5
  • Gender: Male
  • MODDER, REPAIR, CUSTOM IDEAS.
Re: CG2 LED Traces ?
« Reply #1 on: May 10, 2012, 03:11:44 AM »
wish i had a better pic of the traces, but this is what i made off RDC scans,  due to i had some CG2 Traces that were messed up , sorry for the delay been busy  hope this helps out...
« Last Edit: November 30, 2012, 04:17:59 PM by Modded Matt »

 Tracey: I cant believe Rodent of all people made my damn day
3D0: snacks cartoons and naps  lol sounds like rodents typcial day :rofl:
Rodent consoles mods

Offline Tenac

  • Fart Sniffer
  • *
  • Posts: 46
  • Post quality +2/-0
  • Pothead
Re: CG2 LED Traces ?
« Reply #2 on: November 30, 2012, 03:58:19 PM »
I don't mean to gravedig, but I had to fix 2 terminals the other day, and after research I also realized there are no trace pictures of cg2 board's rol for some reason.  They're very easy to visually trace, however.  I didn't see your trace pictures Rodent until just now, but you're right.  Luckily, I got both to work on the first try, and I've never fixed a trace before.


« Last Edit: November 30, 2012, 04:00:26 PM by Tenac »

Offline Modded Matt

  • Site Owner
  • Administrator
  • Around the block
  • *
  • Posts: 4649
  • Post quality +65/-3
  • Gender: Male
Re: CG2 LED Traces ?
« Reply #3 on: November 30, 2012, 04:16:10 PM »
wow, how did you damage both leds?

flood the LED with solder to remove. dont be afraid to bridge the connections.  Below is a video, but I use more solder, the trick is to heat both led pads at the same times and it will "float" right off the pads, then a quick swipe across the led pads will clean any excess solder off the pads.

"TUTORIAL" Lammas Video Led floataion
« Last Edit: November 30, 2012, 04:22:32 PM by Modded Matt »

Offline Tenac

  • Fart Sniffer
  • *
  • Posts: 46
  • Post quality +2/-0
  • Pothead
Re: CG2 LED Traces ?
« Reply #4 on: November 30, 2012, 04:57:10 PM »
wow, how did you damage both leds?

flood the LED with solder to remove. dont be afraid to bridge the connections.  Below is a video, but I use more solder, the trick is to heat both led pads at the same times and it will "float" right off the pads, then a quick swipe across the led pads will clean any excess solder off the pads.

"TUTORIAL" Lammas Video Led floataion
I used to use a big blob of solder to remove them, and I loved that method, but I just got a new soldering iron with a fine tip and it's very hot.  Solder doesn't stick directly to it very well, and I found that melting both sides of the LED by switching off between them rapidly removed the LEDs very easily and quickly.

I've never had this happen before until this new soldering iron.  This method tends to leave very little solder on the contacts, so I add more to them after the LED is removed.

I've repeated this on another controller, and none of the contacts were damaged.

Offline snowcolt17

  • Moderator
  • Acid Modder
  • *
  • Posts: 552
  • Post quality +16/-1
  • Gender: Male
  • If all else fails, reflow it
Re: CG2 LED Traces ?
« Reply #5 on: November 30, 2012, 09:36:30 PM »
I used to use a big blob of solder to remove them, and I loved that method, but I just got a new soldering iron with a fine tip and it's very hot.  Solder doesn't stick directly to it very well, and I found that melting both sides of the LED by switching off between them rapidly removed the LEDs very easily and quickly.

I've never had this happen before until this new soldering iron.  This method tends to leave very little solder on the contacts, so I add more to them after the LED is removed.

I've repeated this on another controller, and none of the contacts were damaged.

here is a video i made a whole ago. nearly a year i believe.

http://youtu.be/L680iE2xops



btw, what i do when i have a messed up trace is use the trace repair pen from radioshack. just scrap the trace and draw over it.
« Last Edit: November 30, 2012, 09:41:16 PM by snowcolt17 »


Offline Rodent

  • XBOX,XBOX360,PS3,WII
  • Moderator
  • Around the block
  • *
  • Posts: 2983
  • Post quality +75/-5
  • Gender: Male
  • MODDER, REPAIR, CUSTOM IDEAS.
Re: CG2 LED Traces ?
« Reply #6 on: November 30, 2012, 10:14:23 PM »
I use 30 awg wire to repair the trace , connect to the led scrap the solid point of the trace where it ends and connect the wire to that.  reason i made that pic of RDC it was so people could see and i tried to reverse the Rol so it would go backwards wiring the diffent  led to a different trace hard to explain i guess, 

which it changed the Rol the way it goes in a circle not in reverse...

 Tracey: I cant believe Rodent of all people made my damn day
3D0: snacks cartoons and naps  lol sounds like rodents typcial day :rofl:
Rodent consoles mods

Offline Tenac

  • Fart Sniffer
  • *
  • Posts: 46
  • Post quality +2/-0
  • Pothead
Re: CG2 LED Traces ?
« Reply #7 on: November 30, 2012, 10:31:57 PM »
I've replaced the LEDs to 10+ controllers without problems using the exact technique as the videos you two posted.  I was just posting how I fixed the traces after what happened when trying a new technique with a new soldering iron, and my success at fixing the lost contacts.  I now know that the blob of solder technique is safer, this was just my first attempt at a new technique, which I learned how sensitive the contact are, especially with a very hot soldering iron.

This thread is about fixing traces, not how to remove LEDs, there's plenty of threads and thousands of videos for that lol.  Now I feel like you guys are acting like I've never done it before and teaching me how to; maybe I should have clarified that in my post.

btw, what i do when i have a messed up trace is use the trace repair pen from radioshack. just scrap the trace and draw over it.
Wow, that's a very cool looking product, and useful in many situations.  I wasn't going to spend $20 on fixing this 1 controller, but I'm glad to know something like this exists.


I use 30 awg wire to repair the trace , connect to the led scrap the solid point of the trace where it ends and connect the wire to that.  reason i made that pic of RDC it was so people could see and i tried to reverse the Rol so it would go backwards wiring the diffent  led to a different trace hard to explain i guess, 

which it changed the Rol the way it goes in a circle not in reverse...
I use 30awg wire for all mods, the insulation slipped off and I didn't care lol.  Ahaha that's a funny idea, but I can see why you got that result instead of what you wanted.
« Last Edit: November 30, 2012, 11:03:37 PM by Tenac »

Offline Modded Matt

  • Site Owner
  • Administrator
  • Around the block
  • *
  • Posts: 4649
  • Post quality +65/-3
  • Gender: Male
Re: CG2 LED Traces ?
« Reply #8 on: February 23, 2013, 09:53:16 AM »
the player one trace in the photo is not corrrect.

The via you show for player 2 isactually player one. player 2 is just below where you show it (under the player one led)

can someone updated the pic please?
« Last Edit: February 23, 2013, 10:05:38 AM by Modded Matt »

Offline snowcolt17

  • Moderator
  • Acid Modder
  • *
  • Posts: 552
  • Post quality +16/-1
  • Gender: Male
  • If all else fails, reflow it
Re: CG2 LED Traces ?
« Reply #9 on: February 23, 2013, 11:18:28 AM »
the player one trace in the photo is not corrrect.

The via you show for player 2 isactually player one. player 2 is just below where you show it (under the player one led)

can someone updated the pic please?

just a sec

thanks for rdc for the scans

here is one i just made

« Last Edit: February 23, 2013, 11:37:54 AM by snowcolt17 »


Offline RDC

  • Administrator
  • Around the block
  • *
  • Posts: 2609
  • Post quality +90/-2
  • Gender: Male
  • The CGnome Project
Re: CG2 LED Traces ?
« Reply #10 on: February 23, 2013, 11:35:26 AM »
CG2 LED Traces


The other controller versions can be seen here - http://forums.xbox-scene.com/index.php?showtopic=512284
« Last Edit: June 26, 2017, 09:33:28 PM by RDC »
Screwing up is one of the best learning tools, so long as the only thing you're not learning is how to screw up.

Offline snowcolt17

  • Moderator
  • Acid Modder
  • *
  • Posts: 552
  • Post quality +16/-1
  • Gender: Male
  • If all else fails, reflow it
Re: CG2 LED Traces ?
« Reply #11 on: February 23, 2013, 11:41:52 AM »
CG2 LED Traces


The other controller versions can be seen here - http://forums.xbox-scene.com/index.php?showtopic=512284


thanks rdc. i posted mine as you were posting yours lol


Offline Modded Matt

  • Site Owner
  • Administrator
  • Around the block
  • *
  • Posts: 4649
  • Post quality +65/-3
  • Gender: Male
Re: CG2 LED Traces ?
« Reply #12 on: February 23, 2013, 11:50:52 AM »
yep, much better.

Offline Rodent

  • XBOX,XBOX360,PS3,WII
  • Moderator
  • Around the block
  • *
  • Posts: 2983
  • Post quality +75/-5
  • Gender: Male
  • MODDER, REPAIR, CUSTOM IDEAS.
Re: CG2 LED Traces ?
« Reply #13 on: February 23, 2013, 02:50:30 PM »
Damn I missed that by a mile 

 Tracey: I cant believe Rodent of all people made my damn day
3D0: snacks cartoons and naps  lol sounds like rodents typcial day :rofl:
Rodent consoles mods

Offline snowcolt17

  • Moderator
  • Acid Modder
  • *
  • Posts: 552
  • Post quality +16/-1
  • Gender: Male
  • If all else fails, reflow it
Re: CG2 LED Traces ?
« Reply #14 on: February 23, 2013, 08:13:04 PM »
Damn I missed that by a mile

old age is kicking in...


 

SMF spam blocked by CleanTalk
SimplePortal 2.3.5 © 2008-2012, SimplePortal