Author Topic: xbox one controller 1537 u10 shorted and seriusly damage (Read 1967 times)

zis2104 · « **on:** June 02, 2021, 03:11:12 PM »

In practice a friend brought me an xbox one controller that like mine does not work the rt button, but the zone of the u10 seems to be completely destroyed ... hall sensor then seems to have received a short not indifferent. Is it possible to fix it in your opinion or is it better to buy a spare board?

https://ibb.co/fXrRKb5

RDC · « **Reply #1 on:** June 02, 2021, 03:19:04 PM »

Damage looks more mechanical to me, like a screw was stuck to the magnet and the Trigger was still pulled a bunch of times. C33 there isn't really required, just make sure that trace is still good so the Hall can get power. If it's dead replace it, no reason to scrap the board from what I can see there.

zis2104 · « **Reply #2 on:** June 02, 2021, 04:07:50 PM »

Ok...from 3 days I will be delivered both hall sensor spare parts and a broken xbox one controller that has the upper 1697 board and the lower 1537 board ... at the limit I can fix a controller

zis2104 · « **Reply #3 on:** June 04, 2021, 09:06:13 AM »

i cleaned up the traces and replaced the hall sensors and now the rt button works fine, but now i wonder since the parts i got from a donor board should i also put c33?
https://ibb.co/rf0Ln4W

RDC · « **Reply #4 on:** June 04, 2021, 09:10:30 AM »

Can if you want, it's not really going to work any better or worse without it.

zis2104 · « **Reply #5 on:** June 04, 2021, 03:37:51 PM »

Another problem, i have replace on xbox one controller 1697 hall sensor rt, and worked for 3 minutes...and the problem return. The hall sensor it's of board donator dead.

zis2104 · « **Reply #6 on:** June 05, 2021, 02:30:25 AM »

nevermind... i have fixed.

wickated · « **Reply #7 on:** June 05, 2021, 06:00:15 AM »

Quote from: zis2104 on June 04, 2021, 03:37:51 PM

Another problem, i have replace on xbox one controller 1697 hall sensor rt, and worked for 3 minutes...and the problem return. The hall sensor it's of board donator dead.

reflow mcu

zis2104 · « **Reply #8 on:** June 05, 2021, 06:35:33 AM »

Quote from: wickated on June 05, 2021, 06:00:15 AM

reflow mcu

No the problem was another, in practice in the assembly I did not push well between the connectors of the boards and in fact if I squeezed them the problem disappeared, I disassembled and reassembled it and it was back in working order

RDC · « **Reply #9 on:** June 05, 2021, 07:07:39 AM »

The Triggers are pretty much contained on the MCU board, so having the top board not plugged in all the way would have caused far more issues than just the one Trigger that you worked on. There is still most likely a suspect solder joint somewhere if squeezing the boards together made it work again, as that caused the entire board to flex in places that you were not even directly pressing. It could have been some other type of short or issue that resolved itself taking it back apart again also, point is I'd keep an eye on that one for a little bit and test play on it awhile to make sure the issue doesn't show back up.

zis2104 · « **Reply #10 on:** June 05, 2021, 07:37:36 AM »

Problem is back.....i should to reflow mcu?

zis2104 · « **Reply #11 on:** June 05, 2021, 08:17:03 AM »

i think the problem are hall sensor .....they are old, when coming new part i try to replace them

zis2104 · « **Reply #12 on:** June 06, 2021, 03:43:55 AM »

A question, if the hall sensors are not the problem, is there any particular resistor or capacitor that I should check?

wickated · « **Reply #13 on:** June 06, 2021, 05:12:24 AM »

u should resolder BOTH hall sensors and then reflow mcu

zis2104 · « **Reply #14 on:** June 06, 2021, 05:29:12 AM »

Quote from: wickated on June 06, 2021, 05:12:24 AM

u should resolder BOTH hall sensors and then reflow mcu

I will try, but I noticed that the problem does not always arise, if I do not use it for hours the problem does not actived, but as soon as I use it for 2-3 minutes it starts to go crazy ..... very strange what do you say?
It gives me the impression that it behaves as if the MSU is getting a wrong voltage from the power board

zis2104 · « **Reply #15 on:** June 06, 2021, 07:01:21 AM »

https://youtube.com/shorts/6L4iCyAp2hI?feature=share this is controller, i have reflow entire board mcu and resolder hall sensor... This is the error.

zis2104 · « **Reply #16 on:** June 08, 2021, 10:32:12 AM »

After spending 3 hours with this controller with various attempts ... I tried to swap the hall sensors of rt lt, because I thought the hall sensor that I soldered to the rt was broken ... I was wrong even if I swapped them it did same mistake. While at lt it was ok. so i thought maybe u10 tracks are gone? could you tell me where those 3 pins are connected? or if maybe there is some area to check in particular?

RDC · « **Reply #17 on:** June 08, 2021, 02:10:32 PM »

The schematic for the 1537 is on the forums here.

zis2104 · « **Reply #18 on:** June 08, 2021, 02:21:22 PM »

Is 1697...but thank

RDC · « **Reply #19 on:** June 08, 2021, 02:27:40 PM »

Triggers work the same way and have the same component designations, they just run to spots on the BGA that you couldn't check. TP spots for the 1697 are in that thread also.

zis2104 · « **Reply #20 on:** August 09, 2021, 04:59:31 PM »

The problem is resistence R39, now my question is the resistence are 0402 value 100k or 100r?

RDC · « **Reply #21 on:** August 09, 2021, 05:10:12 PM »

R39 = 100. There is no k after the value in the schematic, so that means it is just the Ohms value, aka 100 = 100 Ohms. If it were 100 kilOhms, it would say 100k.

zis2104 · « **Reply #22 on:** August 09, 2021, 05:45:42 PM »

Quote from: RDC on August 09, 2021, 05:10:12 PM

R39 = 100. There is no k after the value in the schematic, so that means it is just the Ohms value, aka 100 = 100 Ohms. If it were 100 kilOhms, it would say 100k.

zis2104 · « **Reply #23 on:** November 25, 2021, 03:40:18 AM »

i replaced the resistor and capacitor for rt and i heated the mcu, but it still doesn't work, now i was wondering if the problem was the traces of the 3 pins of the hall sensor. Where should I make the bridges?

News:

Author Topic: xbox one controller 1537 u10 shorted and seriusly damage (Read 1967 times)