Acidmods
Console Modding------ ( Here you can talk about your favorite Consoles ) => PS4 => PS4 Controllers/PS4 Rapid Fire Controllers => Topic started by: Cellstar on August 22, 2021, 04:48:12 AM
-
Hello
I have a problem with left analog. When I play the game the character goes all the time.
Please check the attached controler test and board images.
I have tried replace analog twice time but the problem is still there.
Do you have any suggestion? Please help.
http://ibb.co/Z21HTd5
http://ibb.co/XVKy5kZ
http://ibb.co/7JPVq8J
-
My initial thought was the analog potentiometer needed to be replaced but you said you replaced the whole module twice, I?m assuming with the new ones. From the looks of the motherboard, it may be damaged and that could be causing it? I would?ve done the same steps you did, if it still didn?t work. Motherboards no good🤷🏽♂️ Or try the module on a different motherboard.
-
Some of those vias look like they have been torn out, so that X-axis POT probably isn't getting it's 3.2v to it.
-
My initial thought was the analog potentiometer needed to be replaced but you said you replaced the whole module twice, I?m assuming with the new ones. From the looks of the motherboard, it may be damaged and that could be causing it? I would?ve done the same steps you did, if it still didn?t work. Motherboards no good🤷🏽♂️ Or try the module on a different motherboard.
Thanks for response.
Some of those vias look like they have been torn out, so that X-axis POT probably isn't getting it's 3.2v to it.
Thank you. Can it be fixed somehow? :/
-
Jumper wire from a good 3.2v spot, like the Y-axis 3.2v spot, to the lead of the X-axis 3.2v spot.
Bottom of the board, how your pic is.
O O
+ L3 +
Y
- L3 +
O O
- X +
+ = 3.2v
- = Ground
X = X-axis
Y = Y-axis
L3 = L3 button
O = Solder lugs for the Stick, Ground
-
Jumper wire from a good 3.2v spot, like the Y-axis 3.2v spot, to the lead of the X-axis 3.2v spot.
Bottom of the board, how your pic is.
O O
+ L3 +
Y
- L3 +
O O
- X +
+ = 3.2v
- = Ground
X = X-axis
Y = Y-axis
L3 = L3 button
O = Solder lugs for the Stick, Ground
Thank you very much! :)
-
Ok, I did what you said and is better but not perfect :/
Please take a look:
https://ibb.co/FBH24pf
Do you have any suggestion, please?
-
Ok, I did what you said and is better but not perfect :/
Please take a look:
https://ibb.co/FBH24pf
Do you have any suggestion, please?
Calibrate wheel sensor
-
Ok, I did what you said and is better but not perfect :/
Please take a look:
https://ibb.co/FBH24pf
Do you have any suggestion, please?
Yeah, it's working correctly now. You just need to "calibrate" it. There's multiple ways to go about it. I personally replace the pots until I find one that's centered enough.
-
@zis2104, @ChrisJavier - ok, thank you, I will do that and let you know :)
-
@zis2104, @ChrisJavier - ok, thank you, I will do that and let you know :)
Don't try this https://youtu.be/MIDa3WeNZDI (https://youtu.be/MIDa3WeNZDI)
-
Don't try this https://youtu.be/MIDa3WeNZDI (https://youtu.be/MIDa3WeNZDI)
Thanks for sharing the video. I've ordered some trimmer pots and I'm going to try it soon
-
Thanks for sharing the video. I've ordered some trimmer pots and I'm going to try it soon
good luck