Author Topic: Wiring For 8 Pin Basic Spitfire (Read 9710 times)

xbox modz · « **Reply #1 on:** July 20, 2008, 01:12:36 PM »

Whats the hex code for this 8 pin basic spitfire.
prior thanks for the help.

Nemesis · « **Reply #2 on:** July 20, 2008, 01:52:03 PM »

https://www.acidmods.com/forum/index.php?topic=20459.0

gameroms · « **Reply #3 on:** July 20, 2008, 04:25:35 PM »

just tried it, and doesnt work..

SYSTEM aka (Cyberpyrot) · « **Reply #4 on:** July 20, 2008, 05:20:47 PM »

Quote from: gameroms on July 20, 2008, 04:25:35 PM

just tried it, and doesnt work..

are you sure it is wired as above... if it still does not work I will need an actual chip to test with... Get with King Mike

gameroms · « **Reply #5 on:** July 20, 2008, 06:03:05 PM »

yes sir, wire exactly as above.

KingMike_OS · « **Reply #6 on:** July 20, 2008, 06:21:54 PM »

i'm working on it i will post my result later .. or have a new code out ...
check back here for info later

SYSTEM aka (Cyberpyrot) · « **Reply #7 on:** July 20, 2008, 06:58:39 PM »

Code was tested by mike and it does work there must be a problem with every ones wiring please understand what a floating pin is...

KingMike_OS · « **Reply #8 on:** July 20, 2008, 08:13:40 PM »

Will worked for a like 5 min now the chip get's hot and kills the controller.

Hmm must be the resister need 100K

SYSTEM aka (Cyberpyrot) · « **Reply #9 on:** July 21, 2008, 04:12:39 AM »

yeah try a 100k resistor on the voltage in side..

gameroms · « **Reply #10 on:** July 21, 2008, 09:04:40 AM »

is the the correct way to wire? if so ill tidy up and clean up, and do the left trigger.

proaudiosoft · « **Reply #11 on:** July 22, 2008, 10:22:12 PM »

so is this confirmed working? also, the buttons used, are these momentary switches? last and final question: does the buttons allow for using rapid fire via the triggers? thanks so much and keep up the good work.....

proaudiosoft · « **Reply #12 on:** July 23, 2008, 10:34:43 AM »

so is this confirmed working? also, the buttons used, are these momentary switches? last and final question: does the buttons allow for using rapid fire via the triggers? thanks so much and keep up the good work..... ?????

redryno1221 · « **Reply #13 on:** July 23, 2008, 12:23:31 PM »

it works for some but not others so it may work for you the kinks are still being worked out. Yes they are momentary switches. I don't know what you mean by rapid fire via the triggers, but if you mean the momentary switches control the rapid fire on the triggers than yes.

IDontGetHowtoWire · « **Reply #14 on:** July 23, 2008, 01:11:29 PM »

Can someone explain this diagram to me in complete idiot terms? Thanks

Nemesis · « **Reply #15 on:** July 23, 2008, 01:30:49 PM »

Quote from: redryno1221 on July 23, 2008, 12:23:31 PM

it works for some but not others so it may work for you the kinks are still being worked out. Yes they are momentary switches. I don't know what you mean by rapid fire via the triggers, but if you mean the momentary switches control the rapid fire on the triggers than yes.

nope, he means does it rapid fire through the normal triggers instead of the added button

Quote from: proaudiosoft on July 23, 2008, 10:34:43 AM

so is this confirmed working? also, the buttons used, are these momentary switches? last and final question: does the buttons allow for using rapid fire via the triggers? thanks so much and keep up the good work..... ?????

so the answer is no it rapid fires through the added button

unloopme · « **Reply #16 on:** July 23, 2008, 01:59:12 PM »

Quote from: Nemesis on July 23, 2008, 01:30:49 PM

so the answer is no it rapid fires through the added button

Is there any chance of getting a hex that allows rapid firing through the triggers and use the added buttons to turn it on/off?
I know there's quite a few of us praying for something like this for the PIC12F683.
Thanks in advance.

Nemesis · « **Reply #17 on:** July 23, 2008, 03:10:03 PM »

Quote from: unloopme on July 23, 2008, 01:59:12 PM

Is there any chance of getting a hex that allows rapid firing through the triggers and use the added buttons to turn it on/off?
I know there's quite a few of us praying for something like this for the PIC12F683.
Thanks in advance.

nope not yet, only on a picaxe microchip but that cant be programmed using a conventional pic programmer

http://forums.xbox-scene.com/index.php?showtopic=653455

proaudiosoft · « **Reply #18 on:** July 23, 2008, 04:04:49 PM »

woah, so the microchips being sold by consolecustoms are picaxe? I hope not, I just ordered a kit and was going to rip the hex with my jdm programmer. what's different about the picaxe vs a normal pic that a jdm programmer cant read it? can anyone confirm console customs is selling a picaxe for the 8 pin using exsisting trigger with switches to turn on/off? thanks

KingMike_OS · « **Reply #19 on:** July 23, 2008, 10:59:58 PM »

will don't try to hard to pull the code as they lock there code and when you pull the code

it will damage the code and will not work.

any way as of now i got 683 work but i have open pin problem that means the rapidfire is always

on can't be turn off so need some more testing i been working with 2 other people on this for 3 days

now so as of Now the code is no good and the will not work till i get some result.

This gose for both chip and hex file that was release.

proaudiosoft · « **Reply #20 on:** July 23, 2008, 11:15:01 PM »

well good luck on getting it working mike, keep up the hard work we all appreciate it. If I can be of any assistance let me know......

unloopme · « **Reply #21 on:** July 24, 2008, 08:44:27 AM »

Quote from: KingMike_OS on July 23, 2008, 10:59:58 PM

will don't try to hard to pull the code as they lock there code and when you pull the code it will damage the code and will not work.

Are you 100% sure that they lock their chips???

Nemesis · « **Reply #22 on:** July 24, 2008, 08:56:23 AM »

Quote from: Nemesis on July 24, 2008, 05:34:50 AM

http://forums.xbox-scene.com/index.php?showtopic=656753

i'm assuming the guy pulled the code from the PIC, anyone test to confirm working? i dont have any PIC or even a programmer so i cant do it. though people on ebay say they have put hard work into making the code, that's a load of crap, most of them just pulled the code from someone else.

KingMike_OS · « **Reply #23 on:** July 24, 2008, 10:54:45 AM »

Quote

Are you 100% sure that they lock their chips???

nah i just have nothing better to do so i make up stuff.

any way the hell with the ebay guy. after 2 days of try and error i got it to do this only 4 wire
683 chip and switch this was tested on a new style controller i have not test it on the old ones yet

And here is the old style working same way 4 wire only ...

unloopme · « **Reply #24 on:** July 24, 2008, 06:29:29 PM »

Quote from: KingMike_OS on July 24, 2008, 10:54:45 AM

nah i just have nothing better to do so i make up stuff.

any way the hell with the ebay guy. after 2 days of try and error i got it to do this only 4 wire
683 chip and switch this was tested on a new style controller i have not test it on the old ones yet

<object width="425" height="344"><param name="movie" value="http://www.youtube.com/v/061Dm9Ftb0w&hl=en&fs=1"></param><param name="allowFullScreen" value="true"></param><embed src="http://www.youtube.com/v/061Dm9Ftb0w&hl=en&fs=1" type="application/x-shockwave-flash" allowfullscreen="true" width="425" height="344"></embed></object>

And here is the old style working same way 4 wire only ...

<object width="425" height="344"><param name="movie" value="http://www.youtube.com/v/56vaDy00Je4&hl=en&fs=1"></param><param name="allowFullScreen" value="true"></param><embed src="http://www.youtube.com/v/56vaDy00Je4&hl=en&fs=1" type="application/x-shockwave-flash" allowfullscreen="true" width="425" height="344"></embed></object>

I NEVER meant to question the, King

I was just inquiring because I was going to try and rip the code...but to HELL with that guy!!!
So when can we expect a new hex and wiring diagram, KingMike???
Many thanks, sir for all you efforts!!!

News:

Author Topic: Wiring For 8 Pin Basic Spitfire (Read 9710 times)