Author Topic: NO!!!  (Read 2325 times)

Offline alentris

  • Club AM VIP
  • Acid Modder
  • *
  • Posts: 727
  • Post quality +0/-0
  • Gender: Male
  • Bleep-Bloop.
NO!!!
« on: February 21, 2009, 02:23:42 PM »
 :angry: OK, I'm   :censored: ing pissed right now. So, a while back while putting my psp together, the black lcd tab broke off (The smaller of the two), and shortly after, my psp started having black lines on it. Over about a month, it grew from 1 line to 3. So today I hear that it can be fixed by holding the connecter in place and putting a small piece of paper under it for support. I put it back together, and now It's One huge line in the same place. NOW WHAT!!!! I really don't want to buy a new lcd, because I'd assume that one would break also... Any ideas  :cry2: :beg:

Thanks to HiddenVenom for the sig!

Offline crazyl69

  • Who Farted ???
  • *
  • Posts: 234
  • Post quality +0/-0
Re: NO!!!
« Reply #1 on: February 21, 2009, 07:59:28 PM »
    It sounds like is not your LCD but the LCD connection to the mobo. For some reason the connection is not fully making correct contact. Try to reposition the ribbon cable again and this time try using some electrical tape to keep it from bracking contact and moving around. Good Luck..

Offline blackburn

  • Acid Modder
  • *
  • Posts: 915
  • Post quality +0/-0
  • Gender: Male
  • Xbox 360 Enthusiast and JTAGer
Re: NO!!!
« Reply #2 on: February 21, 2009, 08:26:19 PM »
try putting a piece of tape ONTOP of the connector that goes into the slot


All Sigs Made by ME!

Offline PhenomenalDesigns

  • Granny Spanker
  • *
  • Posts: 476
  • Post quality +0/-0
  • Gender: Male
Re: NO!!!
« Reply #3 on: February 22, 2009, 03:44:40 AM »
Ive had this problem, just get a pair of light, small accurate pliers or tweezers and push the pins really hard down (With the connector in) and make sure you arnt damaging themotherboard, then get some electrical tape and overlay it all, and voila


Hoi! Pinoy ako!

Offline alentris

  • Club AM VIP
  • Acid Modder
  • *
  • Posts: 727
  • Post quality +0/-0
  • Gender: Male
  • Bleep-Bloop.
Re: NO!!!
« Reply #4 on: February 22, 2009, 01:08:13 PM »
I hope it works, because 3 more appeared this morning :cry2:
« Last Edit: February 22, 2009, 01:22:34 PM by alentris »

Thanks to HiddenVenom for the sig!

Offline alentris

  • Club AM VIP
  • Acid Modder
  • *
  • Posts: 727
  • Post quality +0/-0
  • Gender: Male
  • Bleep-Bloop.
Re: NO!!!
« Reply #5 on: March 07, 2009, 10:13:11 AM »
DAMN IT!!!!!!!! I just tried what phen suggested, and now the screen is 100% black!!!! THIS IS MAKING ME SO PISSED OFF!!!

Thanks to HiddenVenom for the sig!

Offline phoenix_s

  • ½ Pint
  • *
  • Posts: 29
  • Post quality +0/-0
  • Gender: Male
Re: NO!!!
« Reply #6 on: March 07, 2009, 10:51:17 AM »
is the whole display black or just the backlight??

plz make a good photo from the connector & i´ll try to hlp you
Sry for my Bad english^^

Offline alentris

  • Club AM VIP
  • Acid Modder
  • *
  • Posts: 727
  • Post quality +0/-0
  • Gender: Male
  • Bleep-Bloop.
Re: NO!!!
« Reply #7 on: March 07, 2009, 11:46:06 AM »
Ok, again. I have about 6 black lines running across the screen. The backlight is  :censored: up. here's the pics:








Thanks to HiddenVenom for the sig!

Offline HellReborn

  • Fart Sniffer
  • *
  • Posts: 41
  • Post quality +0/-0
Re: NO!!!
« Reply #8 on: March 07, 2009, 04:38:03 PM »
do you still have the piece that broke off cause i was able to put mine back on with a small pair or tweezers and it works fine

Offline rceckspurt13

  • Acid Modder
  • *
  • Posts: 637
  • Post quality +2/-0
  • Gender: Male
Re: NO!!!
« Reply #9 on: March 07, 2009, 04:45:00 PM »
That's the same thing I did when mine broke off. Just snap it back On With tweezers and it held.
Any Questions? Please Contact Me: rceckspurt13@gmail.com

Offline alentris

  • Club AM VIP
  • Acid Modder
  • *
  • Posts: 727
  • Post quality +0/-0
  • Gender: Male
  • Bleep-Bloop.
Re: NO!!!
« Reply #10 on: March 07, 2009, 08:01:33 PM »
Nope, it got lost...  :cry2:

Thanks to HiddenVenom for the sig!

Offline phoenix_s

  • ½ Pint
  • *
  • Posts: 29
  • Post quality +0/-0
  • Gender: Male
Re: NO!!!
« Reply #11 on: March 08, 2009, 01:47:14 AM »
i have mine lost too....
my psp connector looks like yours....

use a mircoskope or someting other to look if the conntakts make conntakt....

on the last picture it look like the 2nd conntakt is in air
Sry for my Bad english^^

Offline ApheX

  • Club AM VIP
  • Millennium Poster
  • *
  • Posts: 1094
  • Post quality +1/-0
  • Gender: Male
  • PSP And PSP Slim Case/Hardware Modder
    • ApheX MoDs
Re: NO!!!
« Reply #12 on: March 08, 2009, 03:29:50 AM »
It also looks like your larger lcd connector is not inplace correctly. the lcd backlight shouldn't affect the image. it just lights up the back of the screen. check both connections. you might find that one of the pins on the larger connection might not be pressing down correctly on the cable.

Offline gamerdude767

  • Blogs & Media Member
  • Acid Modder
  • *
  • Posts: 634
  • Post quality +1/-0
  • Gender: Male
Re: NO!!!
« Reply #13 on: March 08, 2009, 03:30:29 AM »
or you could just solder 4 bits of wire from the connector to the pins.. works for me

Quote from: H-Sauce
**Long Pause**........
Yup, thats better than balloons

Offline alentris

  • Club AM VIP
  • Acid Modder
  • *
  • Posts: 727
  • Post quality +0/-0
  • Gender: Male
  • Bleep-Bloop.
Re: NO!!!
« Reply #14 on: March 08, 2009, 08:25:19 AM »
i have mine lost too....
my psp connector looks like yours....

use a mircoskope or someting other to look if the conntakts make conntakt....

on the last picture it look like the 2nd conntakt is in air
my backlight blew out when i tried to push the connectors in with a pair of needlenose pliers.

It also looks like your larger lcd connector is not inplace correctly. the lcd backlight shouldn't affect the image. it just lights up the back of the screen. check both connections. you might find that one of the pins on the larger connection might not be pressing down correctly on the cable.
so let me get this straight: the small connector controls the backlight, the large one controls the actual lcd.

Thanks to HiddenVenom for the sig!

 

SMF spam blocked by CleanTalk
SimplePortal 2.3.5 © 2008-2012, SimplePortal