Drop Shot Mod ?

[KingMike_OS]

Its best to have drop Shot on a tact Butt so press it when needed

Or have Aim Disable So when Aim is Hold It will no Drop Shot

[yasin]

Yes i meant that. The aiming trigger LT.

Cancel dropshot when LT is pressed.

[nycxbox]

That is called Drop Shot with AIM DISABLE..  Many of the main mod makers do that.  I personally don't think it is necessary, but everyone has their preference.  I do not have an AIM disable code on my mod because I don't hook up the chip to the LT. The mod I shared with you guys here - it is very simple.  If you want to disable drop shot you only need to press sync to turn it off.  There are only 2 modes (With and Without Rapid fire) So LT aim disable is unnecessary here, but on a more comprehensive mod I can see the point.

If you want drop shot on a tact you don;t even need a mod.  Let me give you guys a nice schematic that RDC shared with me on building Dropshot into any controller with a tact switch.  I use this for my customer on hard coded mods that don't have a drop shot mode.  What is great about this is it allows you to do a drop shot with the tact button when ever you want.  IF you are using an automatic weapon, the gun will still fire as normal when you press the tact but it will drop.  If you are using a semi auto weapon the tact will fire once and drop you but if you have ANY rapid fire mod enabled it will work with that mod and allow you to drop shot using rapid fire.   

Here is a link to buy the 4066.

http://www.mouser.com/ProductDetail/Texas-Instruments/SN74LV4066AN/?qs=sGAEpiMZZMtxrAS98ir%252bs6Yg1tqWLu1bVp%2fTzCWw%2f6o%3d


Here is the Basic Diagram That RDC gave me.




Let me give you some hints on where to install it and how to install it.

On a Matrix - it will fit here. You will need to bend and cut the pins.  I will see If I can find an install Diagram I did.





On a CG or CG install here.




This is a pretty simple mod just requires some patience when soldering.  I have done of a ton of them they work great.


RDC was kind enough to design me an all in one board to manufacture - I never did.  I might do it though soon an offer these as easy install kits.  I wanted to use Micro 4066 with a quick solder board. Here are the prototypes RDC designed for me.



 

[Rodent]

Nice work and alot of info ..good pics

[KingMike_OS]

Thats Funny Was working on the similar thing same concept heheh nycxbox Beat me to it 









Also have Addon Boards that can be added to any rapidfire on the market and Give you

Dropshot on Tact Switch Working independently or with Rapidfire or QuickKnife Digrams Below. Rodent have few simple to play with Soon

He will right Review About it.

DropShot can work With rapidfire speed so if you have rapidfire On the gun will drop shot with Rapidfire when Tact is press if the Rapidfire is Off

Than The Gun will fire normal Fire rate when the tact is Press and Drop Shot.

Digrams Below

[lovey]

love it thanks very much doing my sons now

Not sure if anyone cares.  But this community has been good to me.  SO here is something you guys here wanted.

This is my Dropshot with auto get up hex. There should be Two modes with and without rapid fire.

12f683

Here you are.

http://www.mediafire.com/?coo1u0yseqs75on

Pin 1 Power
Pin 2 LED
Pin 4 SYNC
Pin 5 B Button
Pin 7 RT trigger
Pin 8 Ground.

[tempermodz]

I just tested this drop shot, Its pretty legit ! I tried on MW2 with the revolver/magnum. The rapid fire is ultra fast with it. It would of been a bonus if it had another mode with just rapid fire not the drop shot. Still pretty legit tho. I wonder If its possible installing to chips, this drop shot & lets say the 3 mode from acid mods, and use that one with the tactical to turn it on/off and the drop shot of course with the sync. Just have one off when using the other mod. But It would be kind of confusing when playing. Also if both are on, maybe the controller will go crazy or damage the chips. Ima see what i can do, and try it out.

Or perhaps using acids original to fire with the tactical button, or any other just firing the second chip with just the rapid fire with a tactical.. I just confused myself here but i'll make it happen

[masterkush]

hey guys, ive recently tried this code with TWO different curcuit boards and it does the same for both. it wont drop BUT if i remove my batterie pack it automatically drops ill post pics of my install later. ps does any 1 have the diagram for the matrix pcb?

[nycxbox]

hey guys, ive recently tried this code with TWO different curcuit boards and it does the same for both. it wont drop BUT if i remove my batterie pack it automatically drops ill post pics of my install later. ps does any 1 have the diagram for the matrix pcb?

THIS DOES NOT WORK ON MATRIX - ONLY CG.

You should use an optocoupler if possible for the install.

IF you are installing on a CG2 make sure you cycle back to off (as the mod will turn on once you put your batter pack in) so after you turn the controller on, cycle the mod back to off then start over should work fine.

Something wring with your install if this is not working for you on a CG or CG2

[masterkush]

THIS DOES NOT WORK ON MATRIX - ONLY CG.

You should use an optocoupler if possible for the install.

IF you are installing on a CG2 make sure you cycle back to off (as the mod will turn on once you put your batter pack in) so after you turn the controller on, cycle the mod back to off then start over should work fine.

Something wring with your install if this is not working for you on a CG or CG2

im sorry to give you a hard time but refrase the second paragraph for me please

[3D0kassiah]

anyone have an install pic of this on a cg2?

[Phantom]

Look at my post in this thread,  I installed it on a cg2. Just have to take the battery pack out to turn it off when the controller is off. https://www.acidmods.com/forum/index.php/topic,39929.msg313231.html#msg313231

[3D0kassiah]

Look at my post in this thread,  I installed it on a cg2. Just have to take the battery pack out to turn it off when the controller is off. https://www.acidmods.com/forum/index.php/topic,39929.msg313231.html#msg313231

pic is blurry

[Phantom]

better?

[Gizmo613]

Not sure if anyone cares.  But this community has been good to me.  SO here is something you guys here wanted.

This is my Dropshot with auto get up hex. There should be Two modes with and without rapid fire.

12f683

Here you are.

http://www.mediafire.com/?coo1u0yseqs75on

Pin 1 Power
Pin 2 LED
Pin 4 SYNC
Pin 5 B Button
Pin 7 RT trigger
Pin 8 Ground.

Can anyone provide a schmetic to make this work for a matrix board. Only looking for the drop shot mod.

[SethMods]

Theodor613,
  There are two main reasons why this code will not work on a Matrix controller. The first is that the triggers operate backwards on a Matrix compared to a CG. So the mod would think that you were pulling the trigger when it was released and releasing the trigger when it was pulled. Second, the Matrix controllers you a "matrix" to connect all of the buttons. So trying to drive the "B" button like you would on a CG will make the controller register multiple button pushes from various buttons instead of just the "B".

If you want I can provide you with a hex file that will work on the Matrix, but at a minimum you would need to wire something like a 2N3906 transistor up to control the B button.

[Gizmo613]

Hey that would be great! Would wiring this up be similar to the one in this post? And thanks for the info on the difference between the controller.

[Famas]

hi Ive installed this at work using the pic 12f683 datasheet and the pinouts given on a cg and I'm only getting one mode on or off when described i should have two how do i change modes ha ha  :Tupi:

[yasin]

Can you explain how this 4066 mod works?

I assume button 1 and button 2 stands for B button and Right trigger.

If so, why do they have both 2 connections?


EDIT: nevermind, got it working.