Author Topic: t0pFire - Fully Loaded Rapidfire System [FREE-RELEASE][2.0 Revision 7] (Read 137041 times)

psyko_chewbacca · « **Reply #180 on:** April 26, 2010, 07:18:51 PM »

Quote from: strpwnedulol on April 26, 2010, 02:26:50 PM

i did the tlc555 timer mod and well... it sucked i hate it it's so slow and then i saw this!!! im doing tonight ill post my results.

You won't be dissapointed mate!

strpwnedulol · « **Reply #181 on:** April 26, 2010, 08:03:40 PM »

i may be anyways, i just finished and well... it doesn't work. i think it might be the chip ill post a picture or 3 Of the controller setup and the chip programmer to let you guys check(what a thing to look forward to!!!)

Modded Matt · « **Reply #182 on:** April 29, 2010, 04:54:09 AM »

use a cg controller, use two 12f683 with gameplayrf those points will work, but are slightly diff on the CG board. good luck, feel free to ask as many questions as you like.

LOONEY2008 · « **Reply #183 on:** May 07, 2010, 09:56:58 AM »

hi and thanks for the time to create the mod tested today very easy to install works on cod and modern warefare sweet tested on battlefield bad company 2 and the left zoom on weapon is on constantly wont turn off so carnt run ect is this a simple fix its a cg controller works sweet on other games just battlefield bad company 2 left trigger seems to be pulled when it isnt any help thanks or is it just a glitch with the code ..
excellent work top

psyko_chewbacca · « **Reply #184 on:** May 07, 2010, 12:35:57 PM »

If you look a couple of post back this issue was alreay discovered and discussed. T0p will look into it for the next revision. It shouldn't be too long. For the time being you can use another controller. I have 2 out of 3 controllers that works perfectly fine in BF:BC2 while the other is giving the problem you are describing.

LOONEY2008 · « **Reply #185 on:** May 07, 2010, 12:59:36 PM »

SORRY DIDNT SEE THAT BIT BUT NOT HAVEING AGO M8 JST FEEDBACK AS REQUESTED BY TOP AT THE BEGINNING OF THE POST

spurgurgle · « **Reply #186 on:** May 08, 2010, 04:01:39 AM »

this trigger problem is back again....... hmm wll i had something along those lines the other day when installing flex fire in my current WIP..... but i didnt instantly go ahhh its the code that must be wrong.......

ok so some games have a more sensitive way of reading trigger pulls..... n i found that halo 3, odst and reach would randomly auto frie with both triggers at the start of everygame with this pad i was making..... so i took the kit off and it was fine or do it would seem.... .... kit back on n it still did it...... so i thought bout it got out a multimeter.... it seemes to me the triggers werent returing all the way down to 0.0V they were settling at 0.2v.... on most gamesthat little wont make a different but on halo it was enough to trick it into thinking i was pulling the triggers.... untill i tap them a few times and the game reconises the release...... i sorted the problem out by remoivnig the pot's for the triggers and putting them back on..... simple as .... well kinda.... took a few attempts to get them in exactualy the right place so the trigger pins read at 0.0 when released...... but now its fine..... yes this wasnt with t0pfire but it was the same problem a few of you have had with t0pfire.... my advice by a multimeter and work out your problems before posting up the same issues over n over again.

LOONEY2008 · « **Reply #187 on:** May 08, 2010, 06:59:03 AM »

got a multimeter in the shed gunna dig it out new to electric so i do apologise if i upset anyone but if i did it was completely unintentional..
as for the pots on the triggers im going to give it a go later today so thankyou for your post also would a if you have a error try this post be applicable as a sticky to help others like me resolve these issues quickly without others haveing to repost the solution?? just a suggestion to help others experianceing the same problem in the future.

psyko_chewbacca · « **Reply #188 on:** May 11, 2010, 07:46:38 AM »

Maybe a little resistor on the trigger lines of the chip could do the trick of lowering the voltage to a near zero value. This could be a temporary fix. T0p said that he'll be working on that in an update. I'm simply waiting and using another controller for the games with issues.

t0pP8uZz · « **Reply #189 on:** May 14, 2010, 07:46:52 AM »

This is on my todo list, t0pFire 3.0. revamp. very busy during the summer, everyone be patient, im not gone anyway. im here. and you will see alot of future work from me. hang in there

psyko_chewbacca · « **Reply #190 on:** May 14, 2010, 08:10:43 AM »

Awesome, I'll be sure to tune in when the time comes!!

lovey · « **Reply #191 on:** May 29, 2010, 05:28:02 AM »

just done this mod on my cg2 and my dads cg2 works very well car'nt wait for the 3.0 to come out thanks t0pP8uZz

FastBrad · « **Reply #192 on:** June 10, 2010, 08:29:37 PM »

Any ETA on v3.0 as of yet. Looking forward to trying it out.

falo21 · « **Reply #193 on:** June 14, 2010, 05:00:32 PM »

can you guys help me i have mod my controller but all it does is change mode but it will not make the guns fire fas i will add a picture of the wiring i did if you can tell where i did and error let me know please.

Sick89 · « **Reply #194 on:** June 17, 2010, 03:25:57 AM »

It looks as if your wiring diagram is a little wrong. The VSS is wired to the Right Trigger. Instead, PIN8 should be wired to the VSS.

Here, check out this diagram:

It seems liked you made a jumper for the Right Trigger to VSS. I believe that's why the Right Trigger isnt working. You're going to have to re-wire it according to the image I posted above.

Modded Matt · « **Reply #195 on:** June 17, 2010, 04:03:07 AM »

falo, you have wired it with your chip upside down, everything is backwards, in your pic the chip's legs are pointing up, in the wiring diagram the chips legs are pointing down.

Hazer · « **Reply #196 on:** June 17, 2010, 05:29:06 AM »

Quote

falo, you have wired it with your chip upside down, everything is backwards, in your pic the chip's legs are pointing up, in the wiring diagram the chips legs are pointing down.

He has the chip upside down, but the wiring is still correct. Its just flipped end-over after soldering it the correct way. Of course I am assuming that the notch is toward the bottom of the controller in his picture. If it is toward the top, then it is all wrong. Cant tell from his pic.

falo21 · « **Reply #197 on:** June 17, 2010, 07:01:47 AM »

Quote from: Hazer on June 17, 2010, 05:29:06 AM

He has the chip upside down, but the wiring is still correct. Its just flipped end-over after soldering it the correct way. Of course I am assuming that the notch is toward the bottom of the controller in his picture. If it is toward the top, then it is all wrong. Cant tell from his pic.

yes hazer i have the notch facing the bottom of the controller i going to try some new frest start i will let u guy know but i done it before and it work but now i can get it to work.

laxboy · « **Reply #198 on:** June 17, 2010, 07:25:12 AM »

ok well some times for me its the wire i dont know why but some times it just doesnt work try it with diffrent wire?

falo21 · « **Reply #199 on:** June 17, 2010, 08:27:21 AM »

Quote from: laxboy on June 17, 2010, 07:25:12 AM

ok well some times for me its the wire i dont know why but some times it just doesnt work try it with diffrent wire?

yeah laxboy i already finish cajnging the cable so i will test it and i will try to post a video of it if it work .but thank everyone for the help hey laxboy do u stay in la

laxboy · « **Reply #200 on:** June 17, 2010, 08:30:36 AM »

as my name no im in jersey i was out there when i made this account years ago on a game and it stuck

falo21 · « **Reply #201 on:** June 17, 2010, 08:34:52 AM »

oh ok hey laxboy i got it to work. it was the cable.can any one send me a link to the reistori need to buy more and im going to try the 18 modes in this week.

Sick89 · « **Reply #202 on:** June 17, 2010, 11:08:44 PM »

If your using a CG controller its a 100 ohm resistor.

Here's a Radioshack link that I use:

http://www.radioshack.com/product/index.jsp?productId=2062339

You can find them elsewhere if your cant find a Radioshack in the area.

falo21 · « **Reply #203 on:** July 02, 2010, 08:06:34 PM »

ok thanks everyone i finally got all done it really work thanks for all the help to everyone it was the cable that was giving me the proble.

FastBrad · « **Reply #204 on:** July 02, 2010, 08:23:45 PM »

Hey admin, spurgs or someone, any news on 3.0 as yet

spurgurgle · « **Reply #205 on:** July 03, 2010, 02:52:28 AM »

yeah a little news on it.. well kinda ...

me n t0p are off on holiday most of the summer so development of t0pfire version 3..... and t0pmap v1 are being put off untill then... dont worry it will happen later this year probilly shortly after the new cod and halo are released so we can test the code on them before making it opensource just to make sure it works to its best ablility on them...

falo21 · « **Reply #206 on:** July 03, 2010, 09:56:25 AM »

hey im havint trouble programing it on this programmer http://cgi.ebay.com/Enhance-JDM-PIC-programmer-Microchip-40pin-ZIF-/310227630524?cmd=ViewItem&pt=LH_DefaultDomain_0&hash=item483b01f9bc
can you guys help please

Modded Matt · « **Reply #207 on:** July 04, 2010, 07:24:13 AM »

do you have the chip in the correct position? look at the brackets for 8 pin on the side of the programmer, line it up it chould be somewhere in the center

RawryP · « **Reply #208 on:** July 05, 2010, 06:41:49 PM »

I don't know if this is in the right section, but:

Would anyone be ready to sell me a complete kit with all the required components for a matrix contoller? With a preprogrammed pic? Because I live nowhere near any electronics stores and I don't have a programmer.

I live in the UK.

gazman321 · « **Reply #209 on:** July 17, 2010, 07:32:24 AM »

Hi guys

I want to install this mod in a wired controller and want to know if its possible ?

I know a wired controller has different VSS/VDD points, would it just be a case of using these different points ?

Thanks

News:

Author Topic: t0pFire - Fully Loaded Rapidfire System [FREE-RELEASE][*2.0 Revision 7*] (Read 137041 times)

Author Topic: t0pFire - Fully Loaded Rapidfire System [FREE-RELEASE][2.0 Revision 7] (Read 137041 times)