3 mode adjustable with jitter mode..updated 06/10/10

[robbo3]

RBO ADJUST.HEX

Same install as hazers burnmeup,
so you use the sync button to change modes

mode1 = dual
mode2 = normal r/f
mode3 = 3 shot burst(if you go to fast  on MW2 it will only shoot 2)
mode4 = off

RBO 2 ADJUST.HEX

mode1 = dual
mode2 = normal r/f
mode3 = cod w@w
mode4 = off

**UPDATE jitter mode added**
RBO JITTER MODE V2

mode1 = dual (bug fixed)
mode2 = cod's
mode3 = jitter
mode4 = off

** UPDATE 2 on/off added**
GP JITTER V1

Same install as GameplayRF/Topfire but pin 3  go's to the Y trace, right tac is mode change and left tack is on/off in any mode,

mode1 = dual
mode2 = cod's
mode3 = jitter
 
speed adjustment

To adjust the speed of any mode hold in the left trigger and press the sync/mode change  button then release the left trigger,

player led will now flash the speed in s.p.s
then quickly flash to show tenths of s.p.s

to increase the speed by +1.0 press RT
to decrease the speed by -1.0 press LT
to increase the speed by +0.1 press the sync/mode change button while the led is flashing the s.p.s
once you reach 0.9 press again to go back to 0

once at your desired speed hold LT and press the sync/mode change button to exit programing.

only tested this on MW2 and W@W so it would be good to know if it works on other games
and only tested on a CG controller but should work on Matrix,


:credit to wondro18 for the original rf source

PLEASE DO NOT PM ME  QUESTIONS POST THEM HERE THANK YOU

*************update 06/10/10*************

I don't have the source for the above codes any more  so I have had to do them again  iv started with the 3 mode adjustable/programmable with jitter and done it a little differently this time and fixed some bugs,also added LT/SYNC  on/off so now its RT/SYNC to program but to exit program mode is still LT/SYNC.

all modes are adjustable / programmable

NEW  3 mode with jitter

mode1 = dual (bugs fixed)
mode 2 = jitter
mode 3 = normal rt only

To program the speed of any mode hold in the RIGHT trigger and press the sync/mode change  button then release the RIGHT trigger,

player led will now flash the speed in s.p.s
then quickly flash to show tenths of s.p.s

to increase the speed by +1.0 press RT
to decrease the speed by -1.0 press LT
to increase the speed by +0.1 press the sync/mode change button while the led is flashing the s.p.s (bug fixed )
once you reach 0.9 press again to go back to 0

once at your desired speed hold LT and press the sync/mode change button to exit programming.

[rafaliyo86]

Awesome!! I will try it this weekend. You always do a great job robbo3

I only have one issue, if you program for exaple 10 sps this speed is for all modes?

R86

[robbo3]

each mode can be set to a different speed

[rafaliyo86]

And to reset it you have to turn off the controller?

[robbo3]

And to reset it you have to turn off the controller?

once you have set the speed it will remember  that speed untill you go into programing mode and  change it again

[rafaliyo86]

ok, once i get home i will try it i cant wait xD

It would be great that when we were trying it we post the best sps for each game. I will do it with my games

Thanks robbo3
R86

[spurgurgle]

this code sounds awsome.... but one question.... how accurate is the speed adjust cos i've notice with a prog kit i have that as little as 0.1sps can make  all the difference in how well the rf works.....????

but still i look forward to testing this code out....

[robbo3]

this code sounds awsome.... but one question.... how accurate is the speed adjust cos i've notice with a prog kit i have that as little as 0.1sps can make  all the difference in how well the rf works.....????

but still i look forward to testing this code out....

forgot to say you can change the speed by 0.1
i have edited my first  post,

[spurgurgle]

cool this sounds like a really cool code.. i always though a 3mode programmable kit would be the ultimate.. ill find out this weekend when i have a mess with it....
Post Merge: February 22, 2010, 05:51:51 AMwow i just had a play around with this code... i installed it on both matrix and cg1

then tested it on cod 6 MW2
GOW2
and Halo 3

well first of the adjustable feature is great
dual works fine
single trigger rf works fine but
burst mode doesnt seem to work at all it is just a 1 shot for each trigger pull.... so i thought maybe adjust the speed a little... took it down  still only 1 shot.... took it up a load still only 1 shot..... then i tried it out on a cg pad with exactly the same results....

[robbo3]

just downloaded the hex to make sure i posted the right one and tested it on MW2 and it fires 3 shots for me.

[spurgurgle]

well i just checked with both pads.. (matrix/cg1) and still the same result......

and before its said there is nothing wrong with my install.... as i took out hazers BMU and re-flashed it with this code. and BMU was fine.....

i'll take the chip out again download the hex again... and test again on a new pic.....
 i can make a vid of my results if needed..... aswell as pis of the install.....

fingers crossed it is only a dodgy chip where its been soldered to and re flashed a few times lol......  ill find out in 15 once i've reflashed nd re-tested
Post Merge: February 22, 2010, 07:59:02 AMok so i just did the re-flash.. and still the same issue with the burst mode.....

and also i noticed on GOW2 that the fire rate isnt very good.... are you using the 25%/75% duty cycle that hazer used to get round the cod 5 patch... because this makes rapid fire on GOW2 dodgy.....

and i beleive this could be causeing the problems with burst mode.. cos when hazer first released BMU3 i set a pic up with a 3 shot burst with the duty cycle and it didnt like it... and would only work on cod5 but would get capped sometimes....??????????

[robbo3]

well i just checked with both pads.. (matrix/cg1) and still the same result......

and before its said there is nothing wrong with my install.... as i took out hazers BMU and re-flashed it with this code. and BMU was fine.....

i'll take the chip out again download the hex again... and test again on a new pic.....
 i can make a vid of my results if needed..... aswell as pis of the install.....

fingers crossed it is only a dodgy chip where its been soldered to and re flashed a few times lol......  ill find out in 15 once i've reflashed nd re-tested
Post Merge: February 22, 2010, 07:59:02 AMok so i just did the re-flash.. and still the same issue with the burst mode.....

and also i noticed on GOW2 that the fire rate isnt very good.... are you using the 25%/75% duty cycle that hazer used to get round the cod 5 patch... because this makes rapid fire on GOW2 dodgy.....

and i beleive this could be causeing the problems with burst mode.. cos when hazer first released BMU3 i set a pic up with a 3 shot burst with the duty cycle and it didnt like it... and would only work on cod5 but would get capped sometimes....??????????

i use two different speeds for press and release to get around the W@W patch,
which might be the problem.

try this one

[spurgurgle]

try this one

try this what????



--------------------------------------
dont worry found it... ill try it out i bit later kinda busy atm... cheers robbo...

[robbo3]

how was mode 1 on halo? what speed did you set it at?

[spurgurgle]

um on halo i left at the standard speed its set to and yeah it was good.... ill do a proper full test with a vid or 2 for you tomoro if i get this issue with the burst mode sorted...... but still this is a great rf

[Ben.]

.... but still this is a great rf

Agrreed! I will PM you in abit robbo

[spurgurgle]

ok robbo i tested that test.hex a min ago....

and firstly was it ment ot be only 1 mode none adjustable (dual trigger....)

well um it fire fine on halo both triggers
i tested it on gears and it reconises that it's rapid firing unlike before... but being set to halo speed its to fast for it......

just as a sugestion you should maybe, somehow make it so you've got your 3modes dual,single,burst and can adjust the speed and whatever just like your original code but with this trigger pull/release timing... (so it works on most fps games like normal..) and then somehow have another button combination say hold both triggers and tap the sycn. to put it into a cod5 trigger pull/release ratio....do you know what i mean....

[robbo3]

ok robbo i tested that test.hex a min ago....

and firstly was it ment ot be only 1 mode none adjustable (dual trigger....)

ok  fixed it i have  added a test 2 attach

[spurgurgle]

cool cheers robbo...

ok so im testing this as i type.....

mode 1 dual works fine on halo and MW2 with speed adjust and everything... 

mode 2 amazing on GOW2, and MW2 and Halo still with speed adjust ... 

but still burst mode is being dodgy....

im using a matrix pad today.... and on halo if i wiggle the trigger (not full pull and release) it will fire in bursts of bout 2-3. which is ok but not quite right compared to other burst modes such as the one on hazers BMU3.

then on MW2 burst didnt do anything. it was 1pull 1shot. and the same on gears of war 2....

both the other modes are fine and dont need messing with.... its just the burst still..... but again man everytime i test this out i like it more and more.... the hammer burst on GOW2 at 7.7sps on mode 2, is wicked and doesnt have to much recol when compared to other rf codes at a similar speed.   


-----------------------------
just ahd a thought... if the burst mode is still being dodgy y not replace it with a second full rf speed so
mode 1 is dual trigger
 mode 2 is single trigger
and mode 3 is single trigger (ocd 5 trigger pull ratio)

or somthing like that.... i dunno.  all i know is this code is awsome or will be when i can get all 3 modes working....

[robbo3]

ok iv replaced burst with a w@w mode,
and attached it to the first post
 

[spurgurgle]

awsome robbo. ill test this out on both pad types again.. and make a video of it for you to ad into your main post if ya like 
Post Merge: February 28, 2010, 07:05:57 AMhi robbo just done a test of this code again... on halo 3 with a matrix pad.... and it all works fine.... i dont have a copy of cod 5 to test o see if mode 3 works past the patch.. but i guess it will...

how ever i did notice a bug withthe dual trigger mode...... (mode 1)

ok turn pad on.....
select mode 1
pulll right trigger = it fires right gun
pull left trigger = it fire left gun
pull both triggers = it fires both guns.
adjust speed on mode 1 tp 11.2 sps
now pull left trigger no rapid fire.
pull right trigger both guns rapid fire....
scroll through all modes back to mode one and left and right triggers are back to bing indepent...

is this a intentional akimbo mode ???
either way its pretty cool being able to fire both guns on the 1 trigger..... i really like this code robbo you've done a great job on it 

[robbo3]

awsome robbo. ill test this out on both pad types again.. and make a video of it for you to ad into your main post if ya like 
Post Merge: February 28, 2010, 07:05:57 AMhi robbo just done a test of this code again... on halo 3 with a matrix pad.... and it all works fine.... i dont have a copy of cod 5 to test o see if mode 3 works past the patch.. but i guess it will...

how ever i did notice a bug withthe dual trigger mode...... (mode 1)

ok turn pad on.....
select mode 1
pulll right trigger = it fires right gun
pull left trigger = it fire left gun
pull both triggers = it fires both guns.
adjust speed on mode 1 tp 11.2 sps
now pull left trigger no rapid fire.
pull right trigger both guns rapid fire....
scroll through all modes back to mode one and left and right triggers are back to bing indepent...

is this a intentional akimbo mode ???
either way its pretty cool being able to fire both guns on the 1 trigger..... i really like this code robbo you've done a great job on it 

there is a akimbo mode in the code but mode 1 should not do it.

[spurgurgle]

hi robbo just wondering if you've had a look into that bug i noted with your last update of this code....

hmm i think its odd knowone has taken a interest in this code cos its awsome....... if i could code this is similar to my idea of a ultimate rf code.......

could you make it so mode one works like this....

still duel trigger but you only need to pull the left trigger or right trigger to fire both guns..... kind of like the bug i noted before.. but stays like it evan after scrolling through all the modes.....??????????

[Ben.]

hmm i think its odd knowone has taken a interest in this code cos its awsome....... if i could code this is similar to my idea of a ultimate rf code.......

I think this code is amazing! Its perfect.. not too many mode's and everything is adjustable!!?!

[nathd]

As stupid as it sounds, can I just check that the second hex works okay on MW2, I'm looking for a constant instead of a burst, many thanks.

[Thejld]

d

[robbo3]

**UPDATE**
RBO JITTER MODE V2

mode1 = dual (bug fixed)
mode2 = cod's
mode3 = jitter
mode4 = off

[nathd]

Great to see the update, what does the jitterv2 do? Many thanks, Nathan.

[Thejld]

Robbo whats the default settings for ur jitter modev1 hex codes? whats the default sps on it, cuz i fiddled with the second one which is for cod, and now it studders and shoots in bursts? Do u know what causes this? thx.

[robbo3]

 10 sps = 10 flashes is the default speed for all modes