Please help support the site by donating at the link below.https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=8ZRU34U47BESW
That Means Its Glitching. And Yes You Can Use The Eject Button For Xell. Also Do You Hear A High PitCh Noise Coming From The Crystal Oscillator? You Should.
Then You Need A Different Crystal, That Thing Is HUGH!!!! Lol I Might Be Able To Solder One Off My Matrix Glitcher. I Was Able To Rgh One Corona With The Same Glitcher From Team Matrix.
I think vgc has them cheap..
Bo You DOnt Need To Write The Ecc Again. Why Didnt You Use The Rgx Files In The First Place? Just curious
Stick To The Corona Numbered Files. Nevermind The Rest. Also The Scan Ip Button Only Works After Xell Has Loaded.Once It Loads, You Hit Scan Ip Then The Ip Address Auto Fills Itself, Then You Hit Get Cpu Key. Its Not Gonna Boot Up Instantly You Might Have To Wait Up To 10 Min Per File.
Failed with 0x0002 Status... is cause your flashing the coolrunner with RGX files , its fine, being its on a slim , those files were for DGX so you get that error when you write the RGX files. your console should of already been wired for RGH2 and if you have the nands loaded up when your flashing the coolrunner it should of already set the settings to RGH2. I will try to get with you later today to help you along , I have a busy schedule so we will see how today goes. Everything was right the last time we talked on skype. and you solved the issue with flashing the coolrunner you should of been able to just flash the coolrunner that was already installed on the console
If You Tried It All Then Itll Only ShoW Xell With The Com Port Monitor.
have you tried shortening the CPU RST wire to try get it to glitch?you can do it without the monitor cable. plug it in to your router, go into the admin settings of your router, go to attached devices, or whatever setting you use to see all devices on the network, once it glitches it will show up as XELL on your network and have its IP next to it, enter the IP into Jrunner and press get CPU key. just refresh your router page every 5 mins or so and wait till it shows up on the network.
it will only show up on the network if it glitches, you should be using the corona timing files in j runner. double check all your wiring to this http://team-xecuter.com/forums/showthread.php/89146-Xecuter-DIY-Corona16-CoolRunner-Free-Upgrade
i still dont understand why you insist on using rgh2 timing files when i have already stated that the slims are based on rgh2 code, but it is completely different in the way it works. the rgh2 timing files you see are for PHAT xbox. you have a corona motherboard stick with the corona files, plain and simple. and yes i would try the alternate ecc file and not the dgx timing file. phantom- by default jrunner will load the appropriate ecc file for dashboard version 15572 and higher, he is on the latest dashboard so by default jrunner loaded the rgx corona ecc. he should try the alternate file. my guess is if the alternate ecc file doesnt work then he is gonna need a better 48mhz crystal oscillator. the corona is very picky on the brand of crystal.
As shown here you can program the coolrunner with RGH timing files for corona ro RGHX files for corona. He is using corona timing files. your totally confusing HIM!!!! and i believe when we started this its on 16202 dashboard so it will be listed as RGH2 on J-runner.
That Right There Is For A Dgx Noy A Coolrunner.
Huy.... If You Go Back In His Post, he Was Using The rgh2 A,B,C,D Timing Files Which Was For The PhaT. For The Corona Timing Files It Doesnt MatterIf You Select Rgh Or Rgh2, The Option For The Corona Timing Files Will Be Available Regardless. Your Picture Proves It. Lol. But Good Luck Heartache, As I Gave Eveything I Know. I Dont Think I Can Be Of More Assistance At This Point. Best Of Luck.
Perfect example of too many chiefs and not enough Indians. This whole thread has been a bunch of back and forth of different information on different ways to do the same thing. Gizmo and Rodent both have different mentalities on how to do something. Pick one person who knows what they are doing to work with and stay on track. This thread has only confused and discouraged anyone who has read it.