« previous next »
Pages: 1 ... 11 12 [13]   Go Down

Author Topic: DualSense 5 Controller PCB Scans  (Read 174600 times)

Offline kumpll2007

  • Guppy
  • *
  • Posts: 1
  • Post quality +0/-0
  • Gender: Male
  • Acidmods User
Re: DualSense 5 Controller PCB Scans
« Reply #360 on: April 04, 2025, 11:21:08 AM »
Hello everyone! After replacing the left stick, it got stuck in the upper left position.


I noticed that some element is missing here, where I highlighted in red. What is this element?


Now, even when I unsoldered the stick, it still stays in the upper left position. Please tell me what I broke.
Logged

Offline RDC

  • Administrator
  • Around the block
  • *
  • Posts: 2639
  • Post quality +90/-2
  • Gender: Male
  • The CGnome Project
Re: DualSense 5 Controller PCB Scans
« Reply #361 on: April 05, 2025, 04:12:33 PM »
Missing part is just a capacitor, that's not needed and isn't causing the issue.

Stuck up/left either both axis lines are shorted to ground, or pulled the plating out of the holes for the voltage to the POTs or pulled the plating out of the holes for the axis.

Logged
Screwing up is one of the best learning tools, so long as the only thing you're not learning is how to screw up.

Offline Para81szs

  • Chief squatting Hard
  • *
  • Posts: 12
  • Post quality +0/-0
  • Acidmods User
Re: DualSense 5 Controller PCB Scans
« Reply #362 on: April 06, 2025, 01:38:30 PM »
@kumpll2007  Your problem is also with the mouths because from what I can see they are a little damaged, especially the lower ones, there is definitely something wrong.
Logged

Offline Para81szs

  • Chief squatting Hard
  • *
  • Posts: 12
  • Post quality +0/-0
  • Acidmods User
Re: DualSense 5 Controller PCB Scans
« Reply #363 on: April 06, 2025, 01:40:01 PM »
Quote from: RDC on April 02, 2025, 03:00:33 PM




Where exactly is it because I can't figure out the position?
Logged

Offline RDC

  • Administrator
  • Around the block
  • *
  • Posts: 2639
  • Post quality +90/-2
  • Gender: Male
  • The CGnome Project
Re: DualSense 5 Controller PCB Scans
« Reply #364 on: April 06, 2025, 06:31:21 PM »
Only 2 connectors on the board that size, and only one of them has anything to do with the R1 button. Also, that image was flipped as I did it top down thru the layers, it's fixed now.
Logged
Screwing up is one of the best learning tools, so long as the only thing you're not learning is how to screw up.

Offline ZhenyaKa

  • ♪♪♪ Tone deff ♪♪♪
  • *
  • Posts: 63
  • Post quality +0/-0
  • Gender: Male
  • Acidmods User
Re: DualSense 5 Controller PCB Scans
« Reply #365 on: April 07, 2025, 01:36:10 PM »
Hello!
Our patient BDM-010

Some times ago I've restore lost resitor for reset PULL-UP. And gamepad was repaired

Gamepad works fine a couple years.

Now I've installed hallsensor stick at left and gamepad randomly powered on or not at all :(

It doesn't turn on more often than it turns on.

Is any point near SIE (CPU) where I can test RESET line from reset button?

At upllup resistor I have 1.8V, at other side of it 0.8V
Logged

Offline Halotestin92

  • Chief squatting Hard
  • *
  • Posts: 10
  • Post quality +0/-0
  • Gender: Male
  • Acidmods User
Re: DualSense 5 Controller PCB Scans
« Reply #366 on: April 17, 2025, 12:35:51 PM »
hello, I got a dualsense bdm 030 with a torn USB socket, the solder pads from the left 4, 6, 8 and 9 were torn off. I regenerated 4, 6 and 8 but 9 probably has no signal because I can't see the path anywhere. Generally, the controller turned on until I soldered a new USB socket (compatible with dualsense). Now after connecting the battery or USB cable it blinks orange twice and doesn't turn on, I've already replaced the Dialog system but still the same. Can someone help?
Logged

Offline EGS2302

  • Guppy
  • *
  • Posts: 2
  • Post quality +0/-0
  • Acidmods User
Re: DualSense 5 Controller PCB Scans
« Reply #367 on: April 24, 2025, 03:14:04 AM »
Hello.

I?ve found one missing components on the PCB. Can someone maybe Meassure it for me or tell me what this component is.

Thank You


3MazInt.jpg" border="0
« Last Edit: April 24, 2025, 03:14:55 AM by EGS2302 »
Logged

Offline RDC

  • Administrator
  • Around the block
  • *
  • Posts: 2639
  • Post quality +90/-2
  • Gender: Male
  • The CGnome Project
Re: DualSense 5 Controller PCB Scans
« Reply #368 on: April 24, 2025, 06:32:28 AM »
7.5k
Logged
Screwing up is one of the best learning tools, so long as the only thing you're not learning is how to screw up.

Offline EGS2302

  • Guppy
  • *
  • Posts: 2
  • Post quality +0/-0
  • Acidmods User
Re: DualSense 5 Controller PCB Scans
« Reply #369 on: April 24, 2025, 08:24:58 AM »
Thank You  :hifive:
Logged
Pages: 1 ... 11 12 [13]   Go Up
« previous next »
 
SMF spam blocked by CleanTalk
SimplePortal 2.3.5 © 2008-2012, SimplePortal