Author Topic: DualSense 5 Controller PCB Scans (Read 456948 times)

kumpll2007 · « **Reply #360 on:** April 04, 2025, 11:21:08 AM »

Hello everyone! After replacing the left stick, it got stuck in the upper left position.

I noticed that some element is missing here, where I highlighted in red. What is this element?

Now, even when I unsoldered the stick, it still stays in the upper left position. Please tell me what I broke.

RDC · « **Reply #361 on:** April 05, 2025, 04:12:33 PM »

Missing part is just a capacitor, that's not needed and isn't causing the issue.

Stuck up/left either both axis lines are shorted to ground, or pulled the plating out of the holes for the voltage to the POTs or pulled the plating out of the holes for the axis.

Para81szs · « **Reply #362 on:** April 06, 2025, 01:38:30 PM »

@kumpll2007 Your problem is also with the mouths because from what I can see they are a little damaged, especially the lower ones, there is definitely something wrong.

Para81szs · « **Reply #363 on:** April 06, 2025, 01:40:01 PM »

Quote from: RDC on April 02, 2025, 03:00:33 PM

Where exactly is it because I can't figure out the position?

RDC · « **Reply #364 on:** April 06, 2025, 06:31:21 PM »

Only 2 connectors on the board that size, and only one of them has anything to do with the R1 button. Also, that image was flipped as I did it top down thru the layers, it's fixed now.

ZhenyaKa · « **Reply #365 on:** April 07, 2025, 01:36:10 PM »

Hello!
Our patient BDM-010

Some times ago I've restore lost resitor for reset PULL-UP. And gamepad was repaired

Gamepad works fine a couple years.

Now I've installed hallsensor stick at left and gamepad randomly powered on or not at all

It doesn't turn on more often than it turns on.

Is any point near SIE (CPU) where I can test RESET line from reset button?

At upllup resistor I have 1.8V, at other side of it 0.8V

Halotestin92 · « **Reply #366 on:** April 17, 2025, 12:35:51 PM »

hello, I got a dualsense bdm 030 with a torn USB socket, the solder pads from the left 4, 6, 8 and 9 were torn off. I regenerated 4, 6 and 8 but 9 probably has no signal because I can't see the path anywhere. Generally, the controller turned on until I soldered a new USB socket (compatible with dualsense). Now after connecting the battery or USB cable it blinks orange twice and doesn't turn on, I've already replaced the Dialog system but still the same. Can someone help?

EGS2302 · « **Reply #367 on:** April 24, 2025, 03:14:04 AM »

Hello.

I?ve found one missing components on the PCB. Can someone maybe Meassure it for me or tell me what this component is.

Thank You

RDC · « **Reply #368 on:** April 24, 2025, 06:32:28 AM »

EGS2302 · « **Reply #369 on:** April 24, 2025, 08:24:58 AM »

Thank You

Worf · « **Reply #370 on:** April 26, 2025, 09:41:17 AM »

Hi. BDM-040 board, I lost this smd resistor when replacing the analogue joystick, the controller isn't recognised, flashes 3 orange lights and then turns off. What's the value?

RDC · « **Reply #371 on:** April 27, 2025, 04:32:51 PM »

Halotestin92 · « **Reply #372 on:** April 28, 2025, 02:50:45 PM »

Hello, dualsense bdm 030 controller, turns on with the button and normally connects via bluetooth to the phone, all buttons and analogies are functional, the problem is that it does not respond to USB, when the battery is disconnected, after connecting the cable it blinks twice orange, which is the same as when there is no battery. After connecting with the battery connected, silence.. the dialog has already been replaced, still the same, different battery, still the same, different cables and also the same. Can someone help?

BuddsControllers · « **Reply #373 on:** May 18, 2025, 02:03:47 AM »

Hi,

I recently purchased some unassembled edge PCBs and thought I would share. I haven't posted a pic here before so don't know how to, I was clicking the button and it just writes

........ anyhow enjoy, I have the trigger boards, module and main board front and back.

https://www.dropbox.com/scl/fo/1yznwrsh7od8az79lgvt4/AGEKS65vzNMpqMm2syfkyS4?rlkey=xb7ro94iil6j0ctzzic40gavs&dl=0

-XP Controllers/Budd's Controllers

Knoxville78 · « **Reply #374 on:** May 23, 2025, 12:41:38 PM »

Hello guys. Need help. I have a BDM-040 board where I am missing smd? does anyone know what its value is? Thanks.

Worf · « **Reply #375 on:** June 12, 2025, 06:50:27 AM »

Hi, I've lost these two components. What are their values?

RDC · « **Reply #376 on:** June 12, 2025, 09:41:44 AM »

Resistor is 5.1k

Cap value isn't really critical.

Padek · « **Reply #377 on:** August 03, 2025, 12:56:36 PM »

Hello, The touchpad on my BDM040 controller isn't working. Replacing the ribbon cable or even replacing the touchpad doesn't help. Where on the motherboard are the resistor or capacitor for the touchpad and button located? The touchpad LEDs light up, button works but there's no response to touch. Resetting the controller doesn't help.

SYN717 · « **Reply #378 on:** August 03, 2025, 11:48:24 PM »

Looking to save my BDM-020 board

* Left stick stuck in this position & L3 button doesn't function when pressed

* Right joystick is fine, nothing wrong on that side.

* Couldn't find any shorts and the points that need 1.8v has them.

* Tried 2 sets of brand new joysticks to rule out any faulty joysticks (all were fine)

Thanks to all who are able to help

Padek · « **Reply #379 on:** August 09, 2025, 05:24:34 PM »

I need help with my BDM-020 motherboard. When connected to USB, it blinks orange twice. When I connect the battery, it doesn't blink, and the computer displays an "unknown device" error. I've already replaced the DA9087 chip and the USB port, and it's still the same. Can anyone help? When I connect it with a cable and battery, the DA9087 and the capacitor underneath it heat up.

szapeboy · « **Reply #380 on:** September 11, 2025, 10:53:38 AM »

Hello, I have a Dualsense BDM-050R controller. It turns on with the PS button and bluetooth works, everything is fine. It charges on charging station, but not charging via USB and not connecting to PC or PS via USB. Removed logic board, without battery when connecting to PC via USB it has 2 red blinks and that's all. With battery connected nothing happens. The USB port itself is in perfect condition, soldering pins are solid.

Any suggestions? Thank you.

szapeboy · « **Reply #381 on:** September 13, 2025, 01:43:24 AM »

Solved. Replaced data line double resistor/fuse.

woyeshizuileye · « **Reply #382 on:** November 11, 2025, 08:53:06 AM »

Two capacitors on my BDM-010 controller were crushed during a Joystick hot-swappable modification, causing the adaptive triggers on the right side of my controller to completely stop working.

I want to know the capacitance values of these two capacitors so I can replace them and restore my controller to normal operation. (Pictures are here.)

You can also view this if the image quality isn't high enough.

Since my English isn't very good, this message was translated using translation software; please excuse.

tawy · « **Reply #383 on:** December 02, 2025, 09:48:59 AM »

Hello,
could you please share to us where a TP via can be found on a BDM-030 motherboard ?
Thank you

edit : found message msg339236, thank you

KeptWolf769 · « **Reply #384 on:** December 05, 2025, 04:41:29 PM »

I just replaced my BDM-040 joysticks with Hall effect joysticks. Everything worked perfectly for a while after being reassembled. It went off just when I was done testing and preparing to calibrate, and has been unresponsive since. I have tried different batteries, but still no response. This is my second time working with a DualSense, and I am a YouTube learner with no formal training in electronics. Can anyone help me out? I swear I can follow instructions. I'm very desperate.

https://1drv.ms/i/c/35b35d5021895f51/EfIDKkFjQpVHrVxMpdFp1NABqR6wXCATQRBMvgtAn3fN6g?e=WY0wTC

KeptWolf769 · « **Reply #385 on:** December 05, 2025, 06:32:00 PM »

Quote from: KeptWolf769 on December 05, 2025, 04:41:29 PM

I just replaced my BDM-040 joysticks with Hall effect joysticks. Everything worked perfectly for a while after being reassembled. It went off just when I was done testing and preparing to calibrate, and has been unresponsive since. I have tried different batteries, but still no response. This is my second time working with a DualSense, and I am a YouTube learner with no formal training in electronics. Can anyone help me out? I swear I can follow instructions. I'm very desperate.

https://1drv.ms/i/c/35b35d5021895f51/EfIDKkFjQpVHrVxMpdFp1NABqR6wXCATQRBMvgtAn3fN6g?e=WY0wTC

Just realised that 3 of the resistors under the SIDE B label came off, any solutions? links to buy replacements or alterations that can be made.

https://1drv.ms/i/c/35b35d5021895f51/EUye6RK11-xAjgOhWdHRfKEBT7_hY7J5ghqWnE6DVD0a9A?e=MpFrKT

RDC · « **Reply #386 on:** December 08, 2025, 07:06:10 AM »

@woyeshizuileye - Those Capacitors are just for decoupling on voltage rails. The exact values are not critical.

@KeptWolf769 - Those Resistors are 4.7k, 0402 size. You can get them at places like Digikey, Mouser and the like online.

Worf · « **Reply #387 on:** December 10, 2025, 07:03:30 AM »

Hi!

I lost this small component from the top of the BDM-040. What is it and what is its value?

RDC · « **Reply #388 on:** December 10, 2025, 07:46:20 AM »

Haven't traced that circuit out, but looks like it's on one of the mic inputs. Measures as 100pF here, 0201 size, but I doubt it's a Capacitor as the thing is black. Haven't seen any caps yet that weren't tan, brown or gray, so I'd guess it's probably some kind of TVS diode.

Nick_Sparkle · « **Reply #389 on:** December 11, 2025, 04:02:20 AM »

I?ve repced the x axis on th left stick playstation 5 controller. Now getting th flashing 3 lights. Where do I run a jumper from the middle pin to? Right pain this, spent ages on it. I?ve obviously damaged something taking it off

News:

Author Topic: DualSense 5 Controller PCB Scans (Read 456948 times)